Biomarkers · Chemical
Myeloperoxidase
- Also listed as
- MPO
- Primary unit
- pmol/L
- LOINC codes
- 66853-3
- Tests that measure Myeloperoxidase
- Labcorp 1, Quest Diagnostics 1
Tests
Check the catalog code, specimen, method and preparation for every test that measures Myeloperoxidase. Select up to five tests to compare them side by side.
Labcorp 1 test
Single-analyte tests
Myeloperoxidase (MPO) 123006
Plasma · Fasting not stated · Turnaround 2 - 4 days
Labcorp catalog pageMethod and collection
- Method
- Latex enhanced immunoturbidimetric method
- Collection
- Collect whole blood using venipuncture techniques. Gently mix the blood with the anticoagulant by inverting sample tube several times (do not shake). Place freshly collected blood samples on ice or in a refrigerator 2°C to 8°C immediately, and store them at 2°C to 8°C until separation. Plasma should be physically separated from cells within two hours of collection by centrifugation at 2°C to 8°C. If a refrigerated centrifuge is not available, chill the centrifuge carrier in the refrigerator before use until cold. Special precaution needs to be taken to ensure transfer of the plasma layer to a polypropylene (not glass) tube while avoiding carryover of any red blood cells or buffy coat white cells. The plasma samples thus prepared may be refrigerated at 2°C to 8°C for five days. If plasma samples are prepared by gel based vacuum tubes, the plasma samples need to be transferred to separated tubes from the top of the gels immediately after the centrifugation. Increased levels of MPO may be observed if the plasma samples are left on the top of the gels for more than eight hours before transferring to separate tubes.
- Reference notes
- • Low CVD Risk: <470 pmol/L • Moderate Risk: 470–539 pmol/L • High Risk: >539 pmol/L
Quest Diagnostics 1 test
Single-analyte tests
Cardio IQ® Myeloperoxidase (MPO) 92814
Plasma · Fasting not stated · Turnaround Set up: Mon-Fri
Quest Diagnostics catalog pageMethod and collection
- Method
- Turbidimetric Immunoassay
- Collection
- 1. Draw and gently invert 8 to 10 times. 2. Centrifuge immediately for 10 minutes at 1300 RCF at room temperature. 3. Pre-squeeze transfer pipet bulb and draw off approximately 2/3 of the upper plasma layer. Note: This ensures that the buffy coat and red cells remain undisturbed. 4. Aliquot plasma into labeled transport tube labeled as “EDTA plasma and cap tightly. Discard original tube. 5. Store transport tube refrigerated at 2-8°C until ready to ship. Store plasma at 2-8°C after collection and ship the same day per packaging instructions provided with the Cleveland HeartLab, Inc. shipping box. Erratic results can be observed if plasma is not centrifuged and separated from red cells immediately.
- Reference notes
- <470 pmol/L
0 of 5 tests selected
Pick one moreSources
1 test: codes, specimens, methods, preparation and reference intervals.
Quest Diagnostics test catalog
1 test: codes, specimens, methods, preparation and reference intervals.
LOINC 66853-3
Regenstrief Institute codes that identify the same result across labs.
Search ClinicalTrials.gov for Myeloperoxidase
Registered studies that measure Myeloperoxidase, on the U.S. National Library of Medicine registry.
Verify these ranges and sources
We compile this page from named laboratory catalogs, guidelines and studies. Labs calculate reference intervals from the people they test, for one assay method and one population group, so an interval describes that population rather than an optimal target.
Interpret your own results with a licensed clinician, or track your lab history and health goals in Aumnivida.
Spotted an error? Email hello@biomarkerlens.com with the page URL and the primary source that corrects the entry.